
Jet Ski
Fuel and Intake Most items are in stock however this is not live inventory |
|||||||
Genuine Mukini Carb Rebuild
Kit 38-44mm $56.95
|
|||||||
Genuine Mukini Carb Rebuild
Kit 46mm $56.95
|
|||||||
Genuine Mukini Carb Rebuild
Kit for Krash 48mm carbs $56.95ea
(order 2 to do both)
|
|||||||
Genuine Mukini Diapharam for
38mm-48mm carbs $17.95ea
Fits Krash 997 (order 2 to do both)
| |||||||
Mukini
Kidney Valve Body Gasket for 38mm-48mm carbs $7.50ea
Fits Krash (order 2 to do both)
| |||||||
Krash Black Ops
Kidney Valve Body aka kidney
plate $32ea (order 2
if you need both)
These are the '21 plates with the smaller hole | |||||||
|
Mikuni Check Valve Grommet Installation Tool $5.95
For installing fuel pump check valve gormmets |
||||||
|
Genuine Keihin carb rebuild kit 38/40
oem and 42mm CDKII $66.95
|
||||||
|
Needle and Seat Krash stock size is 2.3 We also recommned the thicker O-Rings below |
||||||
(o-rings only) |
Thicker Needle and Seat assembly O rings (o-rings only) If you have a fuel leak that is leaking into the engine and filling your crank case with fuel or if you have a rich condition on the low end you cant adjust out then check your needle and seat o-rings. Many carbs leak fuel past the oring causing these problems. Use a pop of pressure gauge to test. These are slightly thicker than the stock o-rings for a tighter fit and seal. Apply a thin amount of 2 stroke oil on o-ring prior to installation. Leaking O rings Video here: https://www.youtube.com/watch?v=rr4VSIaauzA |
||||||
|
Mikuni pop off guage Pump and gauge This is the new and improved version. Specially made for calibrating pop-off pressure. Gauge is calibrated in 1/2 psi increments up to 30 psi. 0-60 and 0-100 gauges are special order only and take about a week to come in. |
||||||
|
Mikuni "Kidney Plate" check
valve This helps stop the fuel dribble in the Krash carbs Double up or even tripple up on these on each carb. BN34/107 |
||||||
5/16" Fuel shut off valve $14
|
|||||||
1/4" Fuel shut off valve
$17
|
|||||||
![]() ![]() WSM Throttle Cables $31.95-$84.95 |
WSM Throttle Cables
High quality with the same OEM design however the lower portion is 6.8mm wide vs the stock 6mm from Krash requiring a slight reaming out of the mounting hole on the carb bracket. |
||||||
![]() |
ADA Racing
Throttle Drum
$24.95ea
Aka throttle wheel for Mikuni carbs, 9 positions, 18mm throw. Works on Krash |
||||||
![]() |
PJS Racing Throttle Drum $33.95ea
Aka throttle wheel for Mikuni carbs, 12 positions, 18mm throw. Works on Krash |
||||||
![]() |
Soft
Throttle Spring
$21.95ea
For Mikuni carbs, Also works on Krash carbs and other carbs based off a Mikuni design. Has 25% less tension than stock. Reduces throttle fatigue. Good/Lubricated throttle cable required. |
||||||
![]() |
Mikuni Coupler
$24.95ea
For Dual Mikuni carbs. |
||||||
![]() ![]() |
Hot Products 1.5, 2.0 and 2.5" Air Filter $56.95-$68.95ea Aka Flame Arrestor. Requires Adaptor sold below. Filters are measured from the bottom of the screen to the very top of the filter. All filters may have small scratches on top. Apparently this happens in manufacturing and is common. The Hot products prefilters will cover it up. Late model Krash stand up skis will fit a 2.5 filter |
||||||
![]() |
Hot Products 2.5" Metallic Air Filter $68.95ea Aka Flame Arrestor. Requires Adaptor sold below. Filters are measured from the bottom of the screen to the very top of the filter. All filters may have small scratches on top. Apparently this happens in manufacturing and is common. The Hot products prefilters will cover it up. Extremely Limited Inventory |
||||||
![]() ![]() ![]() ![]() ![]() ![]() |
Blowsion Flame Arrestors 2.5"
$74.95ea
Requires Adaptor sold below Filters are measured from the bottom of the screen to the very top of the filter. All filters may have small scratches on top. Apparently this happens in manufacturing and is common. The Hot products prefilters will cover it up. Late model Krash stand up skis will fit a 2.5 filter |
||||||
![]() |
Outerwears Prefilter
$24ea
Airfilter sold separately |
||||||
![]() |
Blowsion Prefilter for Tornado filters above
$24ea
Outerwears flame arrestor water-resistant pre-filter screen has a 4" diameter taper fit, 2.5" tall and fits Blowsion, Hot Products and Tau Ceti Tornado flame arrestors; sold individually |
||||||
|
WSM Carburetor Adapter
$22.10ea
Required for upgrade to aftermarket flame arrestor Work well with clamp-on filters from Prok and Blowsion (w/ 2-3/4" i.d. flange) Mounting bolts included |
||||||
|
Krash 997/1200 Flame Arrestor
$44ea
New design, softer material than before |
||||||
|
Krash 997 Carburetor Adapter
$42ea
Required for upgrade to aftermarket flame arrestor Works well with clamp-on filters from Hot Products, Tau Ceti, Prok and Blowsion (w/ 2-3/4" i.d. flange) ON BACK ORDER, sorry but no ETA |
||||||
|
Krash 997 Carburetor Adapter Made in the USA $55ea Required for upgrade to aftermarket flame arrestor aka pod filters, air filters Works well with clamp-on filters from Hot Products, Tau Ceti, Prok and Blowsion (w/ 2-3/4" i.d. flange) |
||||||
|
Krash 997 Carburetor
Upper Carb Gaskets $8.30 ea
You will normally need 2 upper and 2 lower when replacing all. Upper and lower are different sizes. May be green or gray in color. |
||||||
|
Krash 997 Carburetor
Lower Carb Gaskets $10.60ea
You will normally need 2 upper and 2 lower when replacing all. Upper and lower are different sizes. May be green or gray in color. |
||||||
|
Krash 997 Aftermarket Lower/Base Carb Gaskets $4 each You will normally need 2 lower when replacing. Same 48mm id as stock just slightly different shape. Stock Upper and lower gaskets are different sizes but these aftermarket ones can be trimmed and used for either. They are the gray ones pictured with the stock Krash green lower gaskets. If using for uppers you may want to trim the inside too as the stock upper ones have a 50mm id. These are slightly thicker than stock. |
||||||
![]() |
Yamaha Intake Gasket for Dual Carbs
$6ea
OE # 62T-13556-00-00 fits 701 | ||||||
![]() |
Mikuni Carb Gaskets
$3.35ea
38-46mm |
||||||
![]() |
Kehin Carb Gaskets
$3.35ea
38-42mm |
||||||
![]() |
Fuel/Water line kit $48.95ea Economically priced kits fit most fuel/ water line applications. 10ft each of 1/8" primer line, 1/4" fuel line and 3/8" cooling line. Impervious to all octane grades of fuel including racing and aviation fuel. Kink resistant and transparent allowing to visually check fuel or water flow. Made in the U.S.A. |
||||||
![]() |
Fuel/Water line 10' section $18.15ea Fits most fuel/ water line applications. 10ft section available in these sizes 1/8" primer line, 1/4" fuel line or 3/8" cooling line. Not a kit. Impervious to all octane grades of fuel including racing and aviation fuel. Kink resistant and transparent allowing to visually check fuel or water flow. Made in the U.S.A. |
||||||
|
Fuel line 25' rolls
$7.95-24.95ea
Blue Polyurethane Fuel Line. Measurements are for the line inner dimension, ID. |
||||||
|
Fuel Primer Kits
$32.95-36.95ea
FOR SINGLE, DUAL AND TRIPLE CARB APPLICATIONS For removal of stock chokeshaft and plate to provide effortless airflow into the carbs Include all hose fittings and plungers necessary to convert from stock Available for Mikuni and Keihin carbs |
||||||
|
Fuel Primer Kits without carb fittings
$22.95-30.95ea
FOR SINGLE & DUAL APPLICATIONS Includes only hose fittings and plungers as shown or plunger only Works with Mikuni and Keihin style carbs |
||||||
|
Fuel Filters
$7.95-13.95ea
FOR SINGLE, DUAL AND TRIPLE CARB APPLICATIONS Standard 1/4" is the most common |
||||||
|
|||||||
![]() |
Universal check valve 1/4" $7
Allows air to travel in one direction only. Fits 1/4" ID vent line. |
||||||
![]() |
Universal pressure relief valve 1/4" $15
Cracks open at 1.5 psi. Fits 1/4" ID vent line. |
||||||
![]() |
Maxima Quick 2 Mix oil bottle $7
The Maxima Quick 2 Mix bottle has been calibrated to give you the ability to accurately mix in ratios of 24:1 to 100:1. Holds 20oz of oil. |
||||||