Jet Ski Parts, Accessories, Upgrades
|
|||
 Standard Flow Control Valve 3/8" $44.95 Take washers out to adjust. We also recommend the inline filter below. |
Standard Flow Control Valve This flow control valve provides improved throttle response and much quicker starts by drying out your waterbox at low rpm and idle speeds. Tests have shown an average acceleration improvement of 10 feet over a non-equipped model in the first 50 feet. The flow control valve allows unrestricted water flow to the stinger for better top speed, yet controls the amount of water at low speeds for better response. It also allows for an easier tuning of the carburetors. The flow control valve will not interfere with normal engine or exhaust pipe cooling and is compatible with all electronic water injection systems. This model is preset at 3.5 p.s.i. and is adjusted by adding the supplied stainless steel shims to increase the spring tension. Fits all watercraft with OEM or aftermarket exhaust systems (e.g. Factory Pipe) except Yamaha’s with OEM exhaust. Race Legal for All Classes. |
||
   Blowsion Pro Flow Control Valve 3/8" $59.99 Turn valve dial to adjust. We also recommend the inline filter below. |
Jet Works Pro Flow Control Valve This flow control valve provides improved throttle response and much quicker starts by drying out your waterbox at low rpm and idle speeds. Tests have shown an average acceleration improvement of 10 feet over a non-equipped model in the first 50 feet. The flow control valve allows unrestricted water flow to the stinger for better top speed, yet controls the amount of water at low speeds for better response. It also allows for an easier tuning of the carburetors. The flow control valve will not interfere with normal engine or exhaust pipe cooling and is compatible with all electronic water injection systems. This model is preset at 3.5 p.s.i. and is adjusted by turning the nut to increase the spring tension. Fits all watercraft with OEM or aftermarket exhaust systems (e.g. Factory Pipe) except Yamaha’s with OEM exhaust. Last we knew - Race Legal for All Classes. |
||
 PJS Pro Flow Control Valve 3/8" $59.99 Turn valve dial to adjust. We also recommend the inline filter below. |
PJS Pro Flow Control Valve - our favorite This flow control valve provides improved throttle response and much quicker starts by drying out your waterbox at low rpm and idle speeds. Tests have shown an average acceleration improvement of 10 feet over a non-equipped model in the first 50 feet. The flow control valve allows unrestricted water flow to the stinger for better top speed, yet controls the amount of water at low speeds for better response. It also allows for an easier tuning of the carburetors. The flow control valve will not interfere with normal engine or exhaust pipe cooling and is compatible with all electronic water injection systems. This model is adjusted by turning the case to increase the spring tension. Fits all watercraft with OEM or aftermarket exhaust systems (e.g. Factory Pipe) except Yamaha’s with OEM exhaust. Race Legal for All Classes. |
||
 Inline Water Filter 3/8" $18.95 |
Inline Water Filter For use with flow control valve. Does not come with hose clamps |
||
 Water Line Hose Clamp 3/8" $2.25 ea or $19.95 in a 10 pack |
Water Line Hose Clamps For use with flow control valves, filters, fittings and outlets. |
||
 3/8" Transparent waterline piece $2 clear is recommended |
3/8" Transparent waterline piece For use with flow control valve. Goes in-between the flow control valve and the stinger pipe water inlet as pictured. This is just a short piece, not a full hose kit. Clear is recommended. Flow control valve not included. Full Water/Fuel line kits are available HERE |
||
 Krash Trim Assist Bracket $60 |
Krash Trim Assist Bracket
Reduces the amount of pull required to use the trim. Comes with a mounting bolt. Fits all stand up models so far. May not fit Reapers or Predators. We're checking on this. There appears to be a clearance issue with the top of the bracket. We will see about cutting it down and having one specifically for them. Will not work on 2021 with the pulley system. |
||
 Rickter Ninja Foot Holds  Krash Foot Holds  Krash (on left) or Rickter RRP Ninja (right) Foot Holds $399 a pair |
Rickter RRP Ninja Foot Holds If you drill one hole these will bolt bolt right up to the Krash foothold mounts. RRP AB Ninja Binding • Fiberglass • 3.0 lbs (sold in pairs) No Hardware Included Krash Footholds Will fit bigger feet better and the square turf will grip better. These are about a 1/2" wider and longer than the RRP You will need to drill your own mounting holes. Both are super comfortable. |
||
 Rickter RRP Ninja Angled Foothold Wedges $279 a pair Special Order Only (usually 3-5 days) |
Rickter RRP Ninja Angled Foot Hold wedges RRP Rickter Angled Feet Support. Fits Rickter XFS Ninja Competition 2021 and Newer Models. |
||
 Krash 1200 Head Domes $250-$275 pr |
Krash 1200cc Head Domes Stock will set you right around 150-165psi. High compression will get you around 180-185psi Which will run on nonethanol pump gas, 91 Octane.. You MUST run a strong 500CCA or higher battery with these domes. (we recommend the 680CCA here) Sold as a pair. Head orings sold separately here |
||
|
Krash Carburetor/Throttle Body Adapter Made in the USA $80ea Required for upgrade to aftermarket flame arrestor aka pod filters, air filters Works well with clamp-on filters from Hot Products, Tau Ceti, Prok and Blowsion (w/ 2-3/4" i.d. flange) |
||
 |
ProK 2.0" Air Filter $56.95ea Aka Flame Arrestor. Requires Adaptor sold below. Large internal support with parabolic cone that directs and amplifies air volume and velocity for increased top-end performance Round, straight cylinder shape provides even, 360° air intake down the intake tract Constructed of lightweight composite material; weighs from 260g complete Features a lightweight composite clear cone and one-piece molded base Redefine intake performance with an emphasis on convenience Stainless, nonabsorbing element Coast Guard approved Order one per carb Late model Krash stand up skis will fit a 2.5 filter, The Reaper will only fit a 1.5 unless some modification is done. |
||
|
High compression domes are on the
Engine page Lightened Flywheels are on the Electronics page Scupper & Vacate Valves are on the Hull page |
Tech Support & Resources | ||
